HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 68 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

68 | 201

7.3.1 Communicating via MJ1 Serial Port and MJ3 Port

Start by configuring Cscape to use the correct communications port. This can be done using
the Tools

→

Options

→

Communication Port dialog in Cscape.

Next, connect the PC’s serial port to the port labeled MJ1 on

the EXLW/XLW PRIME. If using

MJ3, then the Default Programming port needs to be set in the controller System Menu.

If communications are successful, the target indicator should show the mode of the controller
Target: yy(R) as shown in the status section above.

If the controller is not communicating, it may be required to set the target ID of the controller
in Cscape or on the unit. The Target ID allows directing communications to a particular unit
when multiple units are connected via a CsCAN network. Units without CsCAN network ports
respond to any network ID and do not require the ID to be configured.

To check or change the ID on the EXLW/XLW PRIME, press the System button to enter the
System Menu. The first item in the menu is Set Network ID.

Pressing Enter allows the ID of the unit to be viewed or modified.

To change the Target ID of Cscape use the Controller

→

Set Target Network ID dialog.

«
...
66
67
68
69
70
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Hamworthy Pages: 10

Brand: Fanimation Pages: 2

Brand: M2M Pages: 24

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Watts Pages: 8

Brand: LLURIA Pages: 2

Brand: DSE Pages: 2

Brand: Ascon tecnologic Pages: 16

Brand: KIOUR Pages: 3

Brand: Topway Pages: 14

Brand: Wave Home Solutions Pages: 15

Brand: RKC INSTRUMENT Pages: 10

Brand: K&K Pages: 10

Brand: Hach Pages: 504

VLTAutomationDrive FC 360

Brand: Danfoss Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands