HORNER EXLW PRIME Series User Manual Download

Page: 154 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

154 | 201

16.9 Removable Media (RM) Function Blocks in Cscape

NOTE: For detailed information regarding RM function blocks and parameters, refer to the
Help File

in Cscape Software. Refer ‘USB Flash Media support for RM Functions’ for USB flash

drive access details.

The following RM functional blocks are available in Cscape Software. These function blocks will
reference:

- m

icroSD when filename is prefixed with ‘A:’ or nothing OR

USB A Flash Drive when filename is prefixed with ‘B:’.

Read RM csv

Allows reading of a comma-separated value file from the microSD
interface into the controller register space.

Write RM csv

Allows writing of a comma-separated value file to the microSD
interface from the controller register space.

Rename RM csv

Allows renaming a file on the RM card. The data in the file is not
changed.

Delete RM csv

Allows deleting a file on the RM card

Copy RM csv

Allows copying a file on the RM card. The data in the file is not
changed.

Table 16.1

–

RM Functional Blocks

16.10 Removable Media (RM) Features

—

Program Features

a. Datalog Configuration

—

This feature allows the controller to periodically log register values

to Removable Media. The register data is stored in .CSC (comma separated value) format,
which is compatible with 3

party PC applications, such as Microsoft Excel.

b. Report Editor

—

This feature allows the OCS to be configured to generate text printouts

which incorporate data from the registers embedded in the text. The reports can be printed
using a serial interface printer through any of the serial ports of the OCS or can be saved on
the removable media of the device.

c. Recipes Editor

—

Recipes allow the user to send or update multiple registers simultaneously.

16.11 Removable Media (RM) Features

—

Graphic/Screen Editor

a. Trends

—

The historic support feature in the trend object utilizes Removable Media.

b. Removable Media

—

This is a graphic object used to access files and functions pertaining to

Removable Media.

c. Recipes

—

This is a graphic object that is used in conjunction with the recipe editor which is

mentioned above.

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands