HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 32 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

32 | 201

5.5 View Diags

The View Diags Sub-Menu displays up to 11 System Diagnostics, none of which are editable.

The first two System Diagnostics are critical. If either of these indicate a Fault condition, the
EXLW/XLW PRIME OCS will not enter or remain in Run mode, and the problem must be
investigated and corrected.

Logic Error:

Ok = All executed ladder instructions are legal for loaded firmware
Fault = A ladder instruction not supported by firmware was found

User Program:

Ok = Ladder program and I/O configuration loaded successfully
Fault = Ladder program or I/O configuration not loaded or load failed

The last nine System Diagnostics are informational. If any of these indicate a warning condition,
the EXLW/XLW PRIME OCS can still enter and remain in Run mode, but the problem should be
investigated and corrected.

User Graphics

Ok = Application graphics objects loaded successfully
Fault = Application graphics objects not loaded or load failed

W-Dog Trips

0 = Watchdog timer has not tripped since the last power-up
x = Number of times watchdog timer has tripped

Net Errors

0 = No CAN network bus-off errors have occurred
x = Number of CAN network bus-off errors that have occurred

Network State

Ok = At least one other node was found on the CAN network
Warning = No other nodes were found on the CAN network

Network ID

Ok =

This node’s CAN Network ID is in the range 1 to 253

Warning

= This node’s CAN Network ID was out of range at power

-up

Dup Net ID

Ok

= This node’s Network ID is unique on the CAN network

Warning

= This node’s Network ID is duplicated in another node

Clock Error

Ok = Time and date have been set
Warning = Time and date need to be set

I/O System

Ok = I/O configuration matches the installed I/O and COM modules
Warning = I/O configuration needs updating to match installed modules

Battery

Ok = Backup battery operating properly
Warning = Backup battery needs to be replaced

«
...
30
31
32
33
34
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Aalborg Pages: 128

Brand: Banner Pages: 15

Brand: bar Pages: 2

Brand: Eaton Pages: 288

Brand: Gate Motors Pages: 6

Brand: L. G. B. Pages: 2

Brand: L-Acoustics Pages: 36

Brand: NAD Pages: 4

Brand: NAD Pages: 4

Brand: Valcom Pages: 3

Brand: Valcom Pages: 3

Brand: Valcom Pages: 2

Brand: ISVT Pages: 78

Brand: Linear Technology Pages: 8

Brand: Precision Pages: 8

TRAP-SHUFFLE Game Simulator

Brand: RF SOLUTIONS Pages: 2

Brand: Partlow Pages: 49

Brand: Ascon tecnologic Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands