manualshive.com logo in svg

HORNER EXLW PRIME Series, User Manual

The HORNER EXLW PRIME Series User Manual is an essential guide for operating this advanced product. Designed for easy understanding, this comprehensive manual is available for free download on our website. Explore the limitless possibilities of the HORNER EXLW PRIME Series and download the manual today at manualshive.com.

Share
Download
background image

 

 

MAN1256-05-EN_EXLW_XLWP_UM 

November 10, 2021 

 

 

 

 

185 | 201 

 

21.7  Replacing the Rechargeable Backup Battery 

 
The XLW has an advanced battery system that uses a rechargeable lithium-ion battery. The 
battery  powers  the  real  time  clock  when  power  is  removed.  To  store  registers,  the  battery 
continues to power the OCS for less than a second after external power is removed. In this time 
the registers and other retentive data is saved to internal flash memory. This battery will need 
about eight (8) hours of charging to last approximately two (2) years when powered off.   
 
NOTE: For the registers to be retentive the battery only needs to be charged and present at 
power down. 
 
The battery will generally last seven (7) to ten (10) years. Environmental conditions, including 
extreme temperatures and humidity, can affect battery life.  If the battery is older than seven 
(7) to ten (10) years old, it is recommended that it be replaced as preventative maintenance. 
 
NOTE: Do not use an alkaline AA battery, only the proper battery type listed.  
 
 
 
WARNING: DO NOT USE IF BATTERY IS LEAKING OR HAS BEEN DAMAGED.  
 
WARNING: LITHIUM BATTERIES MAY EXPLODE OR CATCH FIRE IF MISTREATED.  
DO NOT RECHARGE, DISASSEMBLE, HEAT ABOVE 100° C (212° F) INCINERATE, OR 
PUNCTURE. 
 
WARNING: EXPLOSION HAZARD 

–

 BATTERIES MUST BE ONLY BE CHANGED IN A AREA 

KNOWN TO BE NON-HAZARDOUS.  
 
WARNING: Disposal of lithium batteries must be done in accordance with federal, state, and 
local regulations. Be sure to consult with the appropriate regulatory agencies 

before 

disposing batteries. In addition, do not recharge, disassemble, heat or incinerate lithium 
batteries. 
 
WARNING:  Do not make substitutions for the battery. Be sure to only use the authorized part 
number to replace the battery. 
 
 

 
 

 

 

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Gardena 4030 Operating Instructions Manual preview
4030
Brand: Gardena Pages: 17
SAFI DN15 Manual preview
DN15
Brand: SAFI Pages: 18
Badger Meter Orion Series Quick Start Manual preview
Orion Series
Brand: Badger Meter Pages: 2
Badger Meter MDS 2000 Installation And Software Manual preview
MDS 2000
Brand: Badger Meter Pages: 48
Badger Meter BadgerTouch HREBT Manual preview
BadgerTouch HREBT
Brand: Badger Meter Pages: 12
Badger Meter CB-30 User Manual preview
CB-30
Brand: Badger Meter Pages: 16
GAI-Tronics Elemec3 013-02-0095-002 Manual preview
Elemec3 013-02-0095-002
Brand: GAI-Tronics Pages: 12
jbc DDE-1B Manual preview
DDE-1B
Brand: jbc Pages: 44
jbc SKR Instruction Manual preview
SKR
Brand: jbc Pages: 8
Mackie MDR 24/96 User Manual preview
MDR 24/96
Brand: Mackie Pages: 16
TANDBERG MCU Technical Description preview
MCU
Brand: TANDBERG Pages: 47
Packard Bell Slim Remote Control Instruction preview
Slim Remote Control
Brand: Packard Bell Pages: 2
Unipower PCM500 Series Operating Manual preview
PCM500 Series
Brand: Unipower Pages: 24
RADEMACHER 2696 Instruction Manual For The Electrical Connection And For Commissioning preview
2696
Brand: RADEMACHER Pages: 48
Zener SMARTSTART 6000 Networking Manual preview
SMARTSTART 6000
Brand: Zener Pages: 36
Zapi SMART CONSOLE Instructions preview
SMART CONSOLE
Brand: Zapi Pages: 5
Moeller F&G Xcomfort CRCA-00/02 Assembly Instructions preview
F&G Xcomfort CRCA-00/02
Brand: Moeller Pages: 4
IMG STAGELINE 38.1490 Instruction Manual preview
38.1490
Brand: IMG STAGELINE Pages: 14

Brands by name

Popular brands

Load more brands