HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 70 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

70 | 201

7.4 Configuration

An overview of configuration:

1.

Start the configuration by selecting the Controller

→

Hardware Configuration menu

item.

2.

If the EXLW/XLW PRIME OCS is connected to the PC press the Auto Config System
button to automatically detect the Base model, I/O and any communication options.

3.

If the EXLW/XLW PRIME OCS is not connected press the Config button to the right of
the top of the unit. This allows the base CPU to be selected.

4.

Select either EXLW/XLW PRIME OCS CsCAN from the type drop down box.

5.

Once the type of EXLW/XLW PRIME OCS is selected, the model # drop down box will
provide the EXLW/XLW PRIME OCS model numbers from which to choose from.

6.

Once the EXLW/XLW PRIME OCS CPU is selected, press OK to exit the dialog and
configure the I/O that is present in the first slot.

7.

The Hardware Configure dialog (Specifically the Module Setup tab) provides four (4)
buttons to configure all of the I/O. Go through each area of I/O and configure it.

8.

Once done configuring the I/O OK out of configuration dialogs.

Configuring the EXLW/XLW PRIME OCS I/O has four main portions that are covered in this
chapter. For additional information on I/O, refer to the chapters covering

or

in this manual.

«
...
68
69
70
71
72
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Bartlett Pages: 30

Brand: NEC Pages: 146

Brand: Panasonic Pages: 16

Brand: BADODOSECURITY Pages: 8

coviva Smartbox TKP100A

Brand: hager Pages: 4

Brand: Vag Pages: 12

Brand: Yoshitake Pages: 4

Brand: YOKOGAWA Pages: 20

UTAdvanced UT32A

Brand: YOKOGAWA Pages: 3

Optidrive Elevator

Brand: Invertek Pages: 5

Brand: Techtrol Pages: 4

Brand: Daikin Pages: 150

McDonnell & Miller PSE-80 Series

Brand: Xylem Pages: 8

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Pilz Pages: 32

Brand: zeeltronic Pages: 15

Brand: M-system Pages: 3

Brand: DNF Controls Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands