HORNER EXLW PRIME Series User Manual Download

Page: 174 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

174 | 201

Make/Create Clone option enables user to duplicate / Clone application file, all unit
settings and all register values from battery-backed RAM.

Selecting Make Clone brings up the screen below for the user:

Figure 19.3

–

Clone Unit Confirm Screen

After confirmation, the OCS will create two new files in the root directory of the Removable
Media Drive as shown below:

AUTOLOAD.PGM

Application file

CLONE.DAT

File having all unit settings and register values from battery-backed RAM

Figure 19.4

–

Clone Unit Files

NOTE: Make/Create clone operation automatically includes the security in AUTOLOAD.PGM
file for security enabled files.

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands