HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 121 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

121 | 201

Each entry can be configured for one of two types of initiating a transaction: Polled and
Triggered. Polled type entries initiate a transaction with the remote device on every
transaction scan. Triggered type entries only initiate a transaction when a corresponding local
(OCS) binary trigger register is

set

. Once a triggered type transaction completes, the protocol

device driver

resets

the local (OCS) binary register to indicate completion.

These basic types are also subdivided into Read or Write operations. For polled operations, a
Read operation only reads from a remote device. Likewise, a Read/Write operation
continuously reads from the remote device unless the target OCS register value changes from
one ladder scan to another. In this case, the new OCS value is written to the target device. For
triggered operations, only a Read or Write action is available.

When downloaded to the OCS, the Scan List is scanned sequentially to generate data
transactions with the remote device. This transaction scanning can be on a continual basis
(automatic) or controlled from ladder logic (manual) once a complex connection is
programmatically created (i.e., dialup modem). The specific transaction-scanning mode is
selected from the Network Config menu.

The following Horner Automation websites offer OCS Protocol Software Downloads.
North America:

http://hornerautomation.com/support-files/

Europe:

https://www.hornerautomation.eu/product-category/software/configuration-

Please refer to the Cscape Help file for more information on Downloadable Protocols
Configuration. After opening the Cscape Help file, select Contents

→

Networking and

Communications

→

Protocol Configuration.

«
...
119
120
121
122
123
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Gardena Pages: 100

Brand: IBM Pages: 72

Brand: D-Link Pages: 40

Brand: DAV TECH Pages: 10

Brand: Eaton Pages: 2

Brand: Eaton Pages: 2

Brand: Eaton Pages: 8

Ecomot300 AC2630

Brand: IFM Electronic Pages: 111

SIGMA CONTROL 2

Brand: KAESER KOMPRESSOREN Pages: 246

Brand: OBSIDIAN CONTROL SYSTEMS Pages: 13

Brand: KaRo Pages: 12

Brand: Yealink Pages: 8

Brand: Zennio Pages: 30

Brand: Zeta Pages: 13

Brand: IDTECK Pages: 12

Brand: Banner Pages: 2

CGLine+ Web Controller

Brand: Eaton Pages: 28

Brand: ACL Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands