HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 179 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

179 | 201

20.3 Modbus Master Overview

For complete Modbus Master instructions, please refer to the Help file in Cscape.

When acting as a Modbus master, there are two primary mechanisms used by the EXLW/XLW
PRIME to allow the user to specify the data to be read/written from/to the slaves.

Modbus Master Function Block

—

This is for serial only. This is an advanced feature that should

only be used in rare occasions.

Protocol Config

—

The Protocol Config is configured in the Hardware Configuration dialog box

in Cscape (serial)

–

This is the preferred method in most applications.

After the protocol has been selected from the dropdown menu, the Network, Devices, and
Scan List become available. The Protocol Config is configured on three different levels:

•

Network

—

Parameters, such as the polling rate of the data scan, are specified along

with timeout values, retry, and re-acquisition settings. Serial configuration, baud rate,
parity, etc. are also set here.

•

Devices

—

For every slave to be polled, configuration details are added in the Devices

dialog box. This includes Slave ID (serial). Under Device Type, the Modbus addressing

style matching that specified in the slave’s user documentation may be selected. For

instance, some slaves specify Modbus addresses (i.e. 40,001), and others specify
offsets (i.e. 0000).

o

Hex or Decimal

—

Some specify addresses in hex, and others in decimal. By

allowing the user to select the Modbus addressing style for each slave on the
network, minimal address conversion is required. Also, if the slave is another

Horner product (i.e. another OCS), the “Native Addressing” option can be

selected (i.e. %R1, %M17, etc.), and this skips the conversion to Modbus style
altogether.

•

Scan List

—

This is where the specific Modbus addresses to be read/written from/to

each slave are specified. Up to 32 words of data can be read at the same time.

NOTE: Once configuration has been completed on the Network and Devices level,
Modbus data can be directly read/written from graphics objects in the Cscape screen
editor. This is available even if the Modbus register is not listed on the scan list.

NOTE:

The above information is just an introduction to the topic. For more detailed

information, please consult the Cscape Help file.

«
...
177
178
179
180
181
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Fairchild Pages: 2

Brand: Fagor Pages: 103

Brand: Value Point Pages: 7

medialon Showmaster Go

Brand: 7th Sense Pages: 2

Brand: Mackie Pages: 4

Brand: LLURIA Pages: 2

SmarTemp Control fx

Brand: Webasto Pages: 8

FLECK 5810 XTR2

Brand: Pentair Pages: 36

Brand: Eaton Pages: 2

Smart Bias-T SBT-6962690-FFM

Brand: Amphenol Pages: 2

Brand: Jetter Pages: 24

lyriQ AU7394 Series

Brand: On-Q Pages: 8

Sigma II Series

Brand: YASKAWA Pages: 359

Brand: Motroline Pages: 5

Brand: CoolGear Pages: 4

Brand: thermoprozess Pages: 17

Brand: Ebyte Pages: 28

DELTA DEPOSITOR

Brand: Mono Pages: 60

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands