manualshive.com logo in svg

HORNER EXLW PRIME Series, User Manual

The HORNER EXLW PRIME Series User Manual is an essential guide for operating this advanced product. Designed for easy understanding, this comprehensive manual is available for free download on our website. Explore the limitless possibilities of the HORNER EXLW PRIME Series and download the manual today at manualshive.com.

Share
Download
background image

 

 

MAN1256-05-EN_EXLW_XLWP_UM 

November 10, 2021 

 

 

 

 

34 | 201 

 

5.6 

View I/O Slots  

 

 

 
 
The View I/O Slots Sub-Menu displays three System Settings, none of which may be edited. 
 
Internal to the EXLW/XLW PRIME OCS, there is a CPU board, and up to two installed modules. 
Model 0 has no installed I/O or COM modules. All other models have an I/O module and can have 
a user-installed COM module.  
 
Depending  on  which  I/O  module  is  installed  and  which  I/O  module  has  been  configured  by 
Cscape, one of the following six System Settings should appear for Slot 1: 
 

Slot 1: I/O: Empty 

= No I/O module installed or configured 

Slot 1:*Unsupported 

= Unsupported I/O module installed 

Slot 1:-I/O Missing 

= No I/O module installed but an I/O module is configured 

Slot 1:+I/O: XExyy 

 

= yy I/O module installed but no I/O module configured 

Slot 1:?I/O: XExyy 

 

= yy I/O module installed but another I/O module configured 

Slot 1: I/O: XExyy 

 

= yy I/O module installed and configured properly 

 
Depending on the COM module that is installed and the COM module that has been configured 
by Cscape, one of the following six System Settings appears for Slot 2: 
 

Slot 2: I/O: Empty 

  = No COM module installed or configured 

Slot 2:*Unsupported 

= Unsupported COM module installed 

Slot 2:-I/O Missing 

  = No COM module installed but a COM module is configured 

Slot 2:+I/O: XzC 

  = z COM module installed but no COM module configured 

Slot 2:?I/O: XzC 

  =  z  COM  module  installed  but  another  COM  module 

configured 

Slot 2: I/O: XzC 

  = z COM module installed and configured properly 

 
Slot 3: I/O: ETN300   

= ETN300 has been configured through Cscape 

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

K&K M15 Manual preview
M15
Brand: K&K Pages: 6
Gate Motors Q80A Quick Start Manual preview
Q80A
Brand: Gate Motors Pages: 6
Hach sc200 Software Update preview
sc200
Brand: Hach Pages: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Brand: Hach Pages: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Brand: Hach Pages: 472
Hach sc1000 User Manual preview
sc1000
Brand: Hach Pages: 64
V2 ELETTRONICA CL1 Quick Start Manual preview
CL1
Brand: V2 ELETTRONICA Pages: 6
Hach SC4500 Basic User Manual preview
SC4500
Brand: Hach Pages: 210
Uclear Motion Series User Manual preview
Motion Series
Brand: Uclear Pages: 40
Panasonic KX-A16B Quick Start Manual preview
KX-A16B
Brand: Panasonic Pages: 8
Klimaire KUMR-903 Operation Manual preview
KUMR-903
Brand: Klimaire Pages: 5
Viking VC-1000 Technical Practice preview
VC-1000
Brand: Viking Pages: 4
Vag GA Figure 220-D Installation, Operation And Maintenance Manual preview
GA Figure 220-D
Brand: Vag Pages: 6
Grundfos IO 401 Installation And Operating Instructions Manual preview
IO 401
Brand: Grundfos Pages: 20
CALEFFI 677 Series Manual preview
677 Series
Brand: CALEFFI Pages: 10
Watlow EZ-ZONE PM L AAAAB Series User Manual preview
EZ-ZONE PM L AAAAB Series
Brand: Watlow Pages: 30
Carel DPWL Series Quick Start Manual preview
DPWL Series
Brand: Carel Pages: 2
Dantherm HCP 11 Installation And User Manual preview
HCP 11
Brand: Dantherm Pages: 36

Brands by name

Popular brands

Load more brands