HORNER EXLW PRIME Series User Manual Download

Page: 183 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

183 | 201

21.6 Battery Charging Status

Viewed in the System Menu und

er “View Battery Status” or read as a numeric value in

%SR196.
The battery temperature, Tb, is equal to the CPU temperature minus 30°C: Tb = CPU° - 30°C.

Table 21.1

–

Charging State Table

State -

%SR196

Name

Description

Additional Information

Final Charge to 4.2V

The battery is fully charged

Next step, State 12

–

Wait

Discharging

Normal Charging

Battery is fast charging
Tb: 11-45°C

@100mA to 4200mV
Up to 8 hrs charge time

Hot Charging

Battery is slow charging
Tb: 45-60°C

@20mA to 4100mV
Up to 40 hrs charge time

Battery Won’t

Charge

Battery has not completed
charging in 8/40 hours

Charging is suspended for 5
minutes and then tried again.

Battery Too Hot

Not Charging
Tb: > 60°C

Charging cycle resumes when
battery temperature falls to
60°C or less.

Cold Charging

Battery is slow charging
Tb: 0-10°C

@20mA to 4200mV
Up to 40hrs charge time

Battery Too Cold

Not Charging
Tb: < 0°C

Charging cycle resumes when
battery temperature climbs to
0°C or greater.

Error No Battery

No battery was detected at
power up. It will not attempt to
charge until the next power cycle.

%SR55.13 = ON

Final Charge to 4.1V

The battery has fully charged to
4.1V in Hot Charging mode.

4.1V is maintained until
Normal or Cold charging can
execute.

Error: Voltage Too
Low

The battery voltage was too low
at power up. It will not attempt to
charge until the next power cycle.
Make sure a proper battery is
installed.

%SR55.13 = ON

Waiting

The unit has powered up and is
waiting 2 minutes before
attempting to charge.

After 2 minutes, charging
begins even if the battery is
fully charged.

Wait Discharging

The battery has been charged
and the system is waiting for the
voltage to drop before charging
again.

Charging resumes when
battery voltage has dropped
below 4000mV.

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands