HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 188 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

188 | 201

TheXLW Prime OCS uses a lithium coin-type battery with part no. BAT00013, with harness and
connector available from Horner APG.

Below are the steps to replace the battery:

1.

Make sure the user program and any data stored in retentive memory is backed up.

2.

Disconnect all power from theXLW Prime unit including I/O power.

3.

On the back of theXLW Prime model, slide off the battery plate cover.

4.

Connect the new battery into the adjacent connector first and then remove the old
battery.

5.

Dispose of the old battery properly; see the above warning on disposal regulations.

6.

Slide battery plate cover back on the unit.

7.

Apply power to the unit. Check that the battery error is no longer reported. If the unit
still reports the error, remove the battery immediately and contact Technical Support.

«
...
186
187
188
189
190
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Eaton Pages: 86

Brand: Samson Pages: 52

Brand: Radware Pages: 98

Brand: RabbitCore Pages: 34

Brand: Advantech Pages: 2

Vizia RF+ VRP15-1LW

Brand: Leviton Pages: 3

RSF-B mini Series

Brand: Harmonic Drive Pages: 32

Brand: Pilz Pages: 32

Brand: Jetter Pages: 62

Brand: Marmitek Pages: 4

Brand: Qorvo Pages: 45

Brand: Beninca Pages: 23

Veritas R8 Plus

Brand: Texecom Pages: 8

Brand: METRON Pages: 34

Brand: Delta Regis Pages: 15

Brand: Novoferm Pages: 60

Brand: Radarcan Pages: 40

Optima 310 DESIGN

Brand: Genvex Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands