manualshive.com logo in svg

HORNER EXLW PRIME Series, User Manual

The HORNER EXLW PRIME Series User Manual is an essential guide for operating this advanced product. Designed for easy understanding, this comprehensive manual is available for free download on our website. Explore the limitless possibilities of the HORNER EXLW PRIME Series and download the manual today at manualshive.com.

Share
Download
background image

 

 

MAN1256-05-EN_EXLW_XLWP_UM 

November 10, 2021 

 

 

 

 

66 | 201 

 

Table 7.1 

–

 Communication Configuration Dialog  

Target Name 

Name for connection. This is not a mandatory column to be filled, by 

default Cscape will populate ‘Default1’ in edit box.

 

Connection Medium

 

Com Port 

Select this option to communicate over serial communication with the 
device. The port number can be configured here. 

Ethernet 

Select this option to communicate over Ethernet. Provide the IP address 
of the device and select the mode: HE GSM GPRS mode, Built in/ ETN 
Ethernet mode, or HE XEC Ethernet mode. 
 
Select HE GSM GPRS mode if communication with XL series controller on 
GPRS is required and the device has GSM modem installed in XL series 
controller. 

  

Select Built in/ ETN Ethernet mode if the device has on-board Ethernet 
port. 
  
Select HE XEC Ethernet mode if the device has Ethernet comm. option 
board installed in XL series controller.  

  

NOTE: For GPRS connectivity, GPRS configuration from Programs 

→

 

Messaging 

→

 GPRS needs to be done. 

 
NOTE: The controller should support the type of connectivity selected 
and configured for Ethernet communication. 

CAN Interface 

Select this option to communicate over CAN. This option requires 
additional hardware to be installed with the PC to be able to do so. Select 
the type of hardware installed from the dropdown. 

Installed Modem 

Select this option to communicate to the device through the internal 
modem of the computer. Cscape will automatically detect the internal 
modem attached with PC and list in the attached drop down. User can 
select modem and telephone number for target controller. 

NOTE: Cscape will do necessary initialization for the selected internal 
modem. 

USB 

Select this option to communicate over USB. Now Horner devices and 
Horner USB to serial converters are recognized and can be specifically 
selected. 

Connected Device 

NOTE: This configuration is required if the controller to which Cscape is communicating is connected 
to a CsCAN network. 
Connected Device 

By default, this option is selected and networking feature of Cscape is 
disabled. 

Target Node ID 

On selecting this option, Networking feature of Cscape is enabled. CsCAN 
ID for the target controller to be provide here. 

Connection Settings (General Communication Settings) 

Maximum Baud Rate 

Select the baud rate for serial communication. 

Timeout 

Select the communication timeout. 
 
NOTE: Select a larger timeout for GPRS and installed modem 
communication configuration 

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Panasonic FP7 Series Additional Functions Manual preview
FP7 Series
Brand: Panasonic Pages: 45
Unipulse F160 Operation Manual preview
F160
Brand: Unipulse Pages: 99
Accutrol VTS Installation & Operation Manual preview
VTS
Brand: Accutrol Pages: 25
Mainpine EPC Operating Instructions Manual preview
EPC
Brand: Mainpine Pages: 16
Danfoss AFP Series Installation Manual preview
AFP Series
Brand: Danfoss Pages: 20
CALEFFI 543 Series Quick Start Manual preview
543 Series
Brand: CALEFFI Pages: 2
CALEFFI 5350 Series Manual preview
5350 Series
Brand: CALEFFI Pages: 12
Caliber RC20 User Manual preview
RC20
Brand: Caliber Pages: 6
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Brand: Danfoss Pages: 32
Danfoss PVG 16 PVH/Covers Technical Information preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 112
Danfoss PVG 100 Service And Parts Manual preview
PVG 100
Brand: Danfoss Pages: 44
Danfoss PVG 16 PVH/Covers Service And Parts Manual preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 144
Danfoss VLT LCP 11 Installation Instructions preview
VLT LCP 11
Brand: Danfoss Pages: 2
Danfoss VLT FC Series Operating Instructions Manual preview
VLT FC Series
Brand: Danfoss Pages: 64
Danfoss EKC 102A Instructions Manual preview
EKC 102A
Brand: Danfoss Pages: 8
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Brand: Danfoss Pages: 60
Danfoss DHP-A Installation Instruction preview
DHP-A
Brand: Danfoss Pages: 6
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Brand: Danfoss Pages: 4

Brands by name

Popular brands

Load more brands