HORNER EXLW PRIME Series User Manual Download

Page: 114 / 201

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

114 | 201

12.3 Ethernet System Requirements

Full Ethernet functionality requires:

PC running Cscape Programming Software Version 9.3 SP6 or later (for configuration).

EXLW/XLW PRIME controller with onboard Ethernet port.

12.4 Ethernet Module Specifications

Table 12.2

–

Ethernet Module Specifications

Speeds

10 BaseT Ethernet (10Mbps)
100 BaseTx Fast Ethernet (100Mbps)

Modes

Half or Full Duplex

Auto-Negotiation

Both 10/100Mbps and Half/Full Duplex

Connector Type

Shielded RJ-45

Cable Type

(Recommended)

CAT5 (or better) UTP

Port

Auto MDI/MDI-X (Auto Crossover)

Summary of Contents for EXLW PRIME Series










































































































































































































Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands

HORNER EXLW PRIME Series, User Manual

Search results

Summary of Contents for EXLW PRIME Series

Reviews:

Related manuals for EXLW PRIME Series

Brands by name

Popular brands