HORNER EXLW PRIME Series User Manual Download | Manualshive

Page: 147 / 201

background image

MAN1256-05-EN_EXLW_XLWP_UM

November 10, 2021

147 | 201

15.3 Video Properties: Video Type

Figure 15.1

–

Configuring Video Type

There are two options for video type: Stream and Playback

Stream

–

This option can be selected to view live video from a web cam. Four channels are

supported through the USB hub. Only one channel can be viewed at a time. Enter Channel
Number directly or through registers in the Enter Channel No field.

Playback

–

This option can be selected to view videos that are stored in Removable Media on

the controller. Videos present in both A (microSD) and B (USB) drives are supported and can
be viewed. Supported formats including .mp4, .mov, .mpg, and .wmv, can be played.

Select Playback and enter video name in the Enter Target Path field either directly or through
registers.

For example: Test1.mp4 (from microSD) or B:\Test2.mp4 (from USB). Refer to the

Properties: Control

section.

«
...
145
146
147
148
149
...
»

Summary of Contents for EXLW PRIME Series










































































































































































































Reviews:

No comments

Related manuals for EXLW PRIME Series

Brand: Panasonic Pages: 27

Brand: Panasonic Pages: 78

Brand: Panasonic Pages: 98

Brand: NAiS Pages: 173

Brand: Panasonic Pages: 2

Brand: Acclaim Lighting Pages: 32

ESD-5550 Series

Brand: GAC Pages: 12

Brand: Gate Motors Pages: 6

Brand: jcm-tech Pages: 8

Brand: LAE electronic Pages: 7

Brand: LAE electronic Pages: 2

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: Fox Pages: 5

Brand: Watts Pages: 17

Brand: Technische Alternative Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands