manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

Orbit 7120plus/7190g User Guide

35

Beeper Pitch – Error

The beeper pitch codes modify the pitch (frequency) of the sound the scanner 
emits when there is a bad read or error.

 Default = Razz.

Beeper Duration – Good Read

The beeper duration codes modify the length of the beep the scanner emits on a 
good read. 

Default = Normal.

LED – Good Read

The LED indicator can be programmed 

On

 or 

Off

 in response to a good read. 

Default = On.

* Razz (250 Hz)

Medium (3250 Hz)

High (4200 Hz)

* Normal Beep

Short Beep

Short Beep

* LED - Good Read On

LED - Good Read Off

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Cane Creek EC Installation Manuals preview
EC
Brand: Cane Creek Pages: 2
LAZER CORSICA User Manual preview
CORSICA
Brand: LAZER Pages: 19
M-Audio Audio Interface Conectiv User Manual preview
Audio Interface Conectiv
Brand: M-Audio Pages: 18
Targus Chill Mat Quick Start preview
Chill Mat
Brand: Targus Pages: 4
Targus Chill Mat Quick Start Manual preview
Chill Mat
Brand: Targus Pages: 2
Tarot T-2D Quick Start Manual preview
T-2D
Brand: Tarot Pages: 5
YachtSafe W020 Manual preview
W020
Brand: YachtSafe Pages: 4
Samsung SP-M255 User Manual preview
SP-M255
Brand: Samsung Pages: 89
OCTO SmartDiag2GO GD201-O User Manual preview
SmartDiag2GO GD201-O
Brand: OCTO Pages: 5
Razorri SOLIDO R3 User Manual preview
SOLIDO R3
Brand: Razorri Pages: 26
BlueHive 035-6151-2 Manual preview
035-6151-2
Brand: BlueHive Pages: 7
Ikelite 2601.03 Instruction preview
2601.03
Brand: Ikelite Pages: 2
Acebil PE-82MX Operation Manual preview
PE-82MX
Brand: Acebil Pages: 11
Kodak AE-31 Technical Data preview
AE-31
Brand: Kodak Pages: 2
Enviro DRIFTWOOD E30 Owner'S Manual preview
DRIFTWOOD E30
Brand: Enviro Pages: 37
Moulinex Fresh Express Mov' Manual preview
Fresh Express Mov'
Brand: Moulinex Pages: 40
Asong POWER FEED Assembly & Operating Instructions preview
POWER FEED
Brand: Asong Pages: 17
Beurer UWB 55 Instructions For Use Manual preview
UWB 55
Brand: Beurer Pages: 36

Brands by name

Popular brands

Load more brands