manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

94

Orbit 7120plus/7190g User Guide

Interleaved 2 of 5 Length Lock 1

Use a Length Lock code to set a specific length for Interleaved 2 of 5 bar codes. 
Interleaved 2 of 5 codes that do not conform to this length are discarded. To set the 
number for Length Lock 1, scan the bar code below and then scan the digits for the 
length from the 

Programming Chart,

 beginning on page 225. Scan 

Save

 to save 

this setting. 

Default = 0.

Note:

This command can be used together with Length Lock 2 to set a range of allowable 
lengths.

Interleaved 2 of 5 Length Lock 2

Use a Length Lock code to set a specific length for Interleaved 2 of 5 bar codes. 
Interleaved 2 of 5 codes that do not conform to this length are discarded. To set the 
number for Length Lock 2, scan the bar code below and then scan the digits for the 
length from the 

Programming Chart,

 beginning on page 225. Scan 

Save

 to save 

this setting. 

Default = 0.

Note:

This command can be used together with Length Lock 1 to set a range of allowable 
lengths.

Interleaved 2 of 5 Message Length

Scan the bar codes below to change the message length. Refer to 

Message Length 

Description

 (page 86) for additional information. Minimum and Maximum 

lengths = 2-80. Minimum Default = 6, Maximum Default = 80.

Length Lock 1

Length Lock 2

Minimum Message Length

Maximum Message Length

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Canon DADF-M1 General Timing Chart/General Circuit Diagram preview
DADF-M1
Brand: Canon Pages: 16
Canon AE-1 Installation Procedures Manual preview
AE-1
Brand: Canon Pages: 48
NEC NP40 Quick Setup Manual preview
NP40
Brand: NEC Pages: 2
NEC NP1000 Network Setup Manual preview
NP1000
Brand: NEC Pages: 40
Danfoss 176F6516 Installation Manual preview
176F6516
Brand: Danfoss Pages: 14
Dakota Digital Odyssey II Series Quick Start Manual preview
Odyssey II Series
Brand: Dakota Digital Pages: 3
Echo LBP-56V125 Manual preview
LBP-56V125
Brand: Echo Pages: 4
S+S Regeltechnik AERASGARD RCO2-W Operating Instructions, Mounting & Installation preview
AERASGARD RCO2-W
Brand: S+S Regeltechnik Pages: 32
Xerox 5500DN - Phaser B/W Laser Printer Manual preview
5500DN - Phaser B/W Laser Printer
Brand: Xerox Pages: 2
Xerox 3600B - Phaser B/W Laser Printer Install Instructions preview
3600B - Phaser B/W Laser Printer
Brand: Xerox Pages: 2
Takex TX-114TR Instruction Manual preview
TX-114TR
Brand: Takex Pages: 11
GF Signet 2350 Product Manual preview
Signet 2350
Brand: GF Pages: 8
SpectraLink Link 150 M3 Installation And Operation Manual preview
Link 150 M3
Brand: SpectraLink Pages: 51
SimpliPhi PHI 1.3 Installation Manual preview
PHI 1.3
Brand: SimpliPhi Pages: 15
Lexicon MV-5 Service Manual preview
MV-5
Brand: Lexicon Pages: 32
Whispbar K611W Fitting Instructions Manual preview
K611W
Brand: Whispbar Pages: 77
Actia TGU-R ACCESS User Manual preview
TGU-R ACCESS
Brand: Actia Pages: 37
ZipKord Z423A011 Operator'S Manual preview
Z423A011
Brand: ZipKord Pages: 2

Brands by name

Popular brands

Load more brands