manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

108

Orbit 7120plus/7190g User Guide

Addenda Timeout

You can set a time during which the scanner looks for an addenda. If an addenda is 
not found within this time period, the data can be either transmitted or discarded, 
based on the setting you are using for 

UPC-A Addenda Required

. Set the length (in 

milliseconds) for this timeout by scanning the bar code below, then setting the tim-
eout by scanning digits from the 

Programming Chart,

 beginning on page 225 of 

this manual, then 

Save

. 

Default = 300.

Note:

The Addenda Timeout maximum length is determined by the Reread Delay setting. 
See 

Reread Delay

 (page 42). The Addenda Timeout setting is applied to all addenda 

and coupon code searches.

UPC-A Addenda Separator

When this feature is 

On

, there is a space between the data from the bar code and 

the data from the addenda. When turned 

Off

, there is no space. 

Default

=

On.

UPC-A/EAN-13 with Extended Coupon Code

Use the following codes to enable or disable UPC-A and EAN-13 with Extended 
Coupon Code. When left on the default setting (

Off

), the scanner treats Coupon 

Codes and Extended Coupon Codes as single bar codes. 

If you scan the 

Allow Concatenation

 code, when the scanner sees the coupon 

code and the extended coupon code in a single scan, it transmits both as one sym-
bologies. Otherwise, it transmits the first coupon code it reads. 

* Not Required

Addenda Timeout

* On

Off

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Accessory Power ReVIVE series Manual preview
ReVIVE series
Brand: Accessory Power Pages: 36
Young Living Aria Operation Manual preview
Aria
Brand: Young Living Pages: 41
IBAIONDO AR-S Installation Instructions, Use And Maintenance Manual preview
AR-S
Brand: IBAIONDO Pages: 7
UNIT 1 FARO User Manual preview
FARO
Brand: UNIT 1 Pages: 23
Kabuto FIGO Instruction Manual preview
FIGO
Brand: Kabuto Pages: 16
Lanaform Heating Overblanket Instructions For Use Manual preview
Heating Overblanket
Brand: Lanaform Pages: 84
Lanaform Aroma Globe Instruction Manual preview
Aroma Globe
Brand: Lanaform Pages: 84
Lanaform Aroma Design Manual preview
Aroma Design
Brand: Lanaform Pages: 72
Lanaform Aroma Decor Instruction Manual preview
Aroma Decor
Brand: Lanaform Pages: 80
S&B Filters 76-6000 Installation Instructions Manual preview
76-6000
Brand: S&B Filters Pages: 7
Radiola GMRAVPB301 User Manual preview
GMRAVPB301
Brand: Radiola Pages: 51
Tesla V2 SUPERCHARGER First Responder'S Manual preview
V2 SUPERCHARGER
Brand: Tesla Pages: 9
Superpedestrian COPENHAGEN WHEEL User Manual preview
COPENHAGEN WHEEL
Brand: Superpedestrian Pages: 52
Bercomac Berco 700316-4 Owner'S Manual preview
Berco 700316-4
Brand: Bercomac Pages: 20
media-tech MT6350 Instruction Manual preview
MT6350
Brand: media-tech Pages: 13
matev 131 7122 Original Operating Manual preview
131 7122
Brand: matev Pages: 23
Carson HookUpz Smartphone Telescope Adapter Instructions For Use Manual preview
HookUpz Smartphone Telescope Adapter
Brand: Carson Pages: 16
Dometic MOBILE COOLING TROPICOOL TC07 Operating Manual preview
MOBILE COOLING TROPICOOL TC07
Brand: Dometic Pages: 156

Brands by name

Popular brands

Load more brands