manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

Orbit 7120plus/7190g User Guide

75

Search Commands

Search forward for a character

F8

Search the input message forward for “xx” character from the current cursor 
position, leaving the cursor pointing to the “xx” character. 

Syntax = F8xx 

where xx 

stands for the search character’s hex value for its ASCII code. 
Refer to the 

ASCII Conversion Chart (Code Page 1252),

 beginning on page 214 for 

decimal, hex and character codes.

F8 Example: Send bar code data that starts after a particular character

Search for the letter “D” in bar codes and send all the data that follows, including 
the “D.” Using the bar code above:

Command string: 

F844F10D

F8 is the “Search forward for a character” command

44 is the hex value for “D”

F1 is the “Send all characters” command

0D is the hex value for a CR

The data is output as: 

DEFGHIJ
<CR>

Search backward for a character

F9

Search the input message backward for “xx” character from the current cursor 
position, leaving the cursor pointing to the “xx” character. 

Syntax = F9xx 

where xx 

stands for the search character’s hex value for its ASCII code. 
Refer to the 

ASCII Conversion Chart (Code Page 1252),

 beginning on page 214 for 

decimal, hex and character codes.

Search forward for a string

B0

Search forward for “s” string from the current cursor position, leaving cursor 
pointing to “s” string. Syntax = B0nnnnS where nnnn is the string length (up to 
9999), and S consists of the ASCII hex value of each character in the match string. 
For example, B0000454657374 will search forward for the first occurrence of the 4 
character string “Test.”
Refer to the 

ASCII Conversion Chart (Code Page 1252),

 beginning on page 214 for 

decimal, hex and character codes.

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

NEC Nighthawk SX10000D Installation Data preview
Nighthawk SX10000D
Brand: NEC Pages: 10
NEC MultiSync VT440 Installation Data preview
MultiSync VT440
Brand: NEC Pages: 8
NEC MT1056 - MultiSync XGA LCD Projector Quick Connect Manual preview
MT1056 - MultiSync XGA LCD Projector
Brand: NEC Pages: 2
NEC NP1250 Series Network Setup Manual preview
NP1250 Series
Brand: NEC Pages: 17
NEC NP2200 Series Installation And Assembly Manual preview
NP2200 Series
Brand: NEC Pages: 9
NEC NP110 - SVGA DLP Projector Specifications preview
NP110 - SVGA DLP Projector
Brand: NEC Pages: 2
NEC NP216 Series Quick Setup Manual preview
NP216 Series
Brand: NEC Pages: 6
NEC NP110 - SVGA DLP Projector Quick Setup Manual preview
NP110 - SVGA DLP Projector
Brand: NEC Pages: 6
NEC LT75Z - MultiSync SVGA DLP Projector Specifications preview
LT75Z - MultiSync SVGA DLP Projector
Brand: NEC Pages: 2
NEC NP-VE281 Quick Setup Manual preview
NP-VE281
Brand: NEC Pages: 6
NEC NP-V311W User Manual preview
NP-V311W
Brand: NEC Pages: 106
NEC NP-V260 User Manual preview
NP-V260
Brand: NEC Pages: 107
NEC NP-P350W Quick Setup Manual preview
NP-P350W
Brand: NEC Pages: 6
NEC NP-PA500U Specification preview
NP-PA500U
Brand: NEC Pages: 4
NEC NP-PH1400U Installation Manual preview
NP-PH1400U
Brand: NEC Pages: 14
NEC NP-PH1400U User Manual preview
NP-PH1400U
Brand: NEC Pages: 255
NEC NP-PH1400U Specification preview
NP-PH1400U
Brand: NEC Pages: 4
NEC NP-M271X Quick Setup Manual preview
NP-M271X
Brand: NEC Pages: 6

Brands by name

Popular brands

Load more brands