Honeywell ORBIT 7120PLUS User Manual Download Page 88 | Manualshive

Page: 88 / 241

background image

74

Orbit 7120plus/7190g User Guide

03 is the number of characters to move the cursor

F1 is the “Send all characters” command

0D is the hex value for a CR

The data is output as:

4567890ABCDEFGHIJ
<CR>

Move the cursor backward a number of characters

F6

Move the cursor back “nn” characters from current cursor position.

Syntax = F6nn

where nn is the numeric value (00-99) for the number of characters

the cursor should be moved back.

Move the cursor to the beginning

F7

Move the cursor to the first character in the input message.

Syntax = F7.

FE and F7 Example: Manipulate bar codes that begin with a 1

Search for bar codes that begin with a 1. If a bar code matches, move the cursor
back to the beginning of the data and send 6 characters followed by a carriage
return. Using the bar code above:

Command string:

FE31F7F2060D

FE is the “Compare characters” command

31 is the hex value for 1

F7 is the “Move the cursor to the beginning” command

F2 is the “Send a number of characters” command

06 is the number of characters to send

0D is the hex value for a CR

The data is output as:

123456
<CR>

Move the cursor to the end

EA

Move the cursor to the last character in the input message.

Syntax = EA.

«
...
86
87
88
89
90
...
»

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Brand: Eclipse Pages: 6

Brand: Hagan Pages: 32

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Technology Pages: 2

Brand: La Crosse Pages: 2

Brand: Magura Pages: 2

Brand: Zacuto Pages: 5

Brand: PAC Pages: 4

Brand: PAC Pages: 4

SX-70 SODR-X-TRACTOR

Brand: Pace Pages: 2

Brand: PAC Pages: 8

Brand: QIMMIQ Pages: 16

Brand: QA1 Pages: 10

Brand: Samsung Pages: 89

Brand: Samsung Pages: 57

Brand: Nectre Fireplaces Pages: 232

Evolion 2.1 kWh

Brand: Saft Pages: 4

Brand: A&D Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands