manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

Orbit 7120plus/7190g User Guide

41

Poor Quality Codes

Poor Quality 1D Codes

This setting improves the scanner’s ability to read damaged or badly printed linear 
bar codes. When

 Poor Quality 1D Reading On

 is scanned, poor quality linear bar 

code reading is improved, but the scanner’s snappiness is decreased, making it 
less aggressive when reading good quality bar codes. This setting does not affect 
2D bar code reading. 

Default = Poor Quality 1D Reading Off.

Poor Quality PDF Codes

This setting improves the scanner’s ability to read damaged or badly printed PDF 
codes by combining information from multiple images. When 

Poor Quality PDF 

On

 is scanned, poor quality PDF code reading is improved, but the scanner’s snap-

piness is decreased, making it less aggressive when reading good quality bar 
codes. This setting does not affect 1D bar code reading. 

Default = Poor Quality PDF 

Reading Off.

Left of 

Presentation Centering 

Window

Right of Presentation 

Centering Window

Poor Quality 1D Reading On

* Poor Quality 1D Reading Off

Poor Quality PDF Reading On

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Canon IMAGEPRESS C7010VPS Brochure & Specs preview
IMAGEPRESS C7010VPS
Brand: Canon Pages: 4
D-Link DCS-60 Technical Specifications preview
DCS-60
Brand: D-Link Pages: 2
StoneAge AUTOSTROKE AST-200-V2 User Manual preview
AUTOSTROKE AST-200-V2
Brand: StoneAge Pages: 28
Manfrotto 357 Instructions preview
357
Brand: Manfrotto Pages: 2
Makita ER400MP Original Instruction Manual preview
ER400MP
Brand: Makita Pages: 64
Makita RBC260 Service Information preview
RBC260
Brand: Makita Pages: 12
E-Vision 6500 series Information Manual preview
6500 series
Brand: E-Vision Pages: 23
Gardigo MARTEN-FREE CAR Instruction Manual preview
MARTEN-FREE CAR
Brand: Gardigo Pages: 36
Pitney Bowes F625 Operating Manual preview
F625
Brand: Pitney Bowes Pages: 22
Cateye VELO5 Operation Instructions preview
VELO5
Brand: Cateye Pages: 2
UPOWER Ecoline UE-12Li100BL IN Series Installation Manual preview
UE-12Li100BL IN Series
Brand: UPOWER Ecoline Pages: 2
Takex TX-114TR Instruction Manual preview
TX-114TR
Brand: Takex Pages: 11
GF Signet 2350 Product Manual preview
Signet 2350
Brand: GF Pages: 8
SpectraLink Link 150 M3 Installation And Operation Manual preview
Link 150 M3
Brand: SpectraLink Pages: 51
A&D AD-4328 Specification preview
AD-4328
Brand: A&D Pages: 4
Ikelite Canon PowerShot A700 Instruction Manual preview
Canon PowerShot A700
Brand: Ikelite Pages: 6
Raytel LLC TellPhone 4200 Installation Instructions & Operating Manual preview
TellPhone 4200
Brand: Raytel LLC Pages: 40
Olympus Waterproof Case PT-17 Instruction Manual preview
Waterproof Case PT-17
Brand: Olympus Pages: 38

Brands by name

Popular brands

Load more brands