Honeywell ORBIT 7120PLUS User Manual Download Page 222 | Manualshive

Page: 222 / 241

background image

208

Orbit 7120plus/7190g User Guide

Replace Cables

The standard interface cable is attached to the scanner with an 10-pin modular
connector. When properly seated, the connector is held in the scanner’s base by a
flexible retention tab. The interface cable is designed to be field replaceable.

•

Order replacement cables from Honeywell or from an authorized distributor.

•

When ordering a replacement cable, specify the cable part number of the
original interface cable.

Replace an Interface Cable

1. Turn off the power to the host system.

2. Disconnect the scanner’s cable from the terminal or

computer.

3. Locate the small hole underneath the base. This is the

cable release.

4. Straighten one end of a paper clip.

5. Insert the end of the paper clip into the small hole and

press in. This depresses the retention tab, releasing the
connector. Pull the connector out while maintaining
pressure on the paper clip, then remove the paper clip.

6. Replace with the new cable.

Insert the connector into the opening and press firmly.
The connector is keyed to go in only one way, and will click into place.

Troubleshoot the Scanner

The scanner automatically performs self-tests whenever you turn it on. If your
scanner is not functioning properly, review the following Troubleshooting Guide to
try to isolate the problem.

Is the power on?

If the LEDs aren’t illuminated, check that:

•

The cable is connected properly.

•

The host system power is on (if external power isn’t used).

Is the scanner having trouble reading your symbols?

If the scanner isn’t reading symbols well, check that the symbols:

•

Aren’t smeared, rough, scratched, or exhibiting voids.

•

Aren’t coated with frost or water droplets on the surface.

•

Are enabled in the scanner or in the decoder to which the scanner connects.

Cable
Release

«
...
220
221
222
223
224
...
»

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

mydlink DSP-W110

Brand: D-Link Pages: 13

Brand: D-Link Pages: 44

Brand: Tao Motor Pages: 3

Brand: Acer Pages: 12

Brand: Acer Pages: 67

Brand: Acer Pages: 2

Brand: Uebler Pages: 18

Brand: Oki Pages: 2

Brand: hepco & becker Pages: 4

Brand: hepco & becker Pages: 2

STARSHOOT 52173

Brand: Orion Pages: 8

Allen-Bradley 42GLP-9000-QD

Brand: Rockwell Automation Pages: 10

Brand: Brodit Pages: 2

Brand: ADT Pages: 22

1997-2007 Dodge Dakota Telescoping Computer Base C-TCB-28

Brand: Havis-Shields Pages: 3

Brand: BOXLIGHT Pages: 55

Brand: Pyle Pages: 4

Brand: Blink Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands