manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

Orbit 7120plus/7190g User Guide

97

Code 93 Message Length

Scan the bar codes below to change the message length. Refer to 

Message Length 

Description

 (page 86) for additional information. Minimum and Maximum 

lengths = 0-80. Minimum Default = 0, Maximum Default = 80.

Code 93 Append

This function allows the scanner to append the data from several Code 93 bar 
codes together before transmitting them to the host computer. When this function 
is enabled, the scanner stores those Code 93 bar codes that start with a space 
(excluding the start and stop symbols), and does not immediately transmit the 
data. The scanner stores the data in the order in which the bar codes are read, 
deleting the first space from each. The scanner transmits the appended data when 
it reads a Code 93 bar code that starts with a character other than a space. 

Default = Off.

Code 93 Code Page

Code pages define the mapping of character codes to characters. If the data 
received does not display with the proper characters, it may be because the bar 
code being scanned was created using a code page that is different from the one 
the host program is expecting. If this is the case, scan the bar code below, select 
the code page with which the bar codes were created (see 

ISO 2022/ISO 646 

Off

Minimum Message Length

Maximum Message Length

On

* Off

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

VDO M5 Short Instruction Manual preview
M5
Brand: VDO Pages: 91
CALEFFI 7200 Series Operating Steps - Installation Manual preview
7200 Series
Brand: CALEFFI Pages: 20
Campbell CWS Series Instruction Manual preview
CWS Series
Brand: Campbell Pages: 70
3M Overhead Projector 2660 Operating Instructions Manual preview
Overhead Projector 2660
Brand: 3M Pages: 12
3M Multimedia Projector X65 Quick Start Manual preview
Multimedia Projector X65
Brand: 3M Pages: 6
3M Multimedia Projector X62w Operator'S Manual preview
Multimedia Projector X62w
Brand: 3M Pages: 71
Yuasa NP Series Manual preview
NP Series
Brand: Yuasa Pages: 35
3M WS Series User Instructions preview
WS Series
Brand: 3M Pages: 10
IGNIA LIGHT NANO Installation And Maintenance Manual preview
NANO
Brand: IGNIA LIGHT Pages: 12
Wallbox Commander 2 Installation And User Manual preview
Commander 2
Brand: Wallbox Pages: 7
Abicor Binzel SR 9 Operating Instructions Manual preview
SR 9
Brand: Abicor Binzel Pages: 44
Opus-Two Instrument Control System User Manual preview
Instrument Control System
Brand: Opus-Two Pages: 8
MICRO-EPSILON scanCONTROL 25 100 Series Operating Instructions Manual preview
scanCONTROL 25 100 Series
Brand: MICRO-EPSILON Pages: 60
Dynojet 24xLC2 Linx Installation Manual preview
24xLC2 Linx
Brand: Dynojet Pages: 68
Kuda-Phonebase 283410 Installation Instruction preview
283410
Brand: Kuda-Phonebase Pages: 3
PRAXIS M24 Girder Quick Manual preview
M24 Girder
Brand: PRAXIS Pages: 2
COOLFORT CF-0233 Manual Instruction preview
CF-0233
Brand: COOLFORT Pages: 16
Godox V860IIIN Instruction Manual preview
V860IIIN
Brand: Godox Pages: 31

Brands by name

Popular brands

Load more brands