Honeywell ORBIT 7120PLUS User Manual Download Page 80 | Manualshive

Page: 80 / 241

background image

66

Orbit 7120plus/7190g User Guide

If you have changed data format settings, and wish to clear all formats and return
to the factory defaults, scan the Default Data Format code below.

Add a Data Format

Step 1.

Scan the

Enter Data Format

symbol (

).

Step 2.

Select

Primary/Alternate Format

Determine if this will be your primary data format, or one of 3 alternate
formats. This allows you to save a total of 4 different data formats. To
program your primary format, scan

0

Programming Chart,

beginning on page 225. If you are programming an alternate format,
scan

1, 2

, or

3

, depending on which alternate format you are

programming. (See

Primary/Alternate Data Formats

further information.)

Step 3.

Terminal Type

Refer to

Terminal ID Table

(page 68) and locate the Terminal ID number

for your PC. Scan three numeric bar codes from the

Programming Chart,

beginning on page 225, to program the scanner for your terminal ID (you
must enter 3 digits). For example, scan

0 0 3

for an AT wedge.

Note: 099

indicates all terminal types.

Step 4.

Code I.D.

Symbology Charts,

beginning on page 211, find the symbology to

which you want to apply the data format. Locate the Hex value for that
symbology and scan the 2 digit hex value from the

Programming Chart,

beginning on page 225.

If you wish to create a data format for all symbologies, with the exception
of some specific symbologies, refer to B8 (

).

If you are creating a data format for Batch Mode Quantity, use 35 for the
Code I.D.

Note: 99

indicates all symbologies.

Step 5.

Length

Specify what length (up to 9999 characters) of data will be acceptable for
this symbology. Scan the four digit data length from the

beginning on page 225. For example, 50 characters is entered as

0050

.

Note: 9999

indicates all lengths.

Step 6.

Editor Commands

Refer to

Data Format Editor Commands

(page 68). Scan the symbols that

represent the command you want to enter.

* Default Data Format

«
...
78
79
80
81
82
...
»

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Brand: Manfrotto Pages: 2

Brand: Panasonic Pages: 2

Brand: Panasonic Pages: 2

CYRC50U - UNIVERSAL REAR-VIEW CAMERA

Brand: Panasonic Pages: 20

Brand: Panasonic Pages: 12

Brand: Panasonic Pages: 54

Brand: Samsung Pages: 2

Brand: Samsung Pages: 15

Brand: OFFCARR Pages: 12

Brand: OEM Tools Pages: 4

FireCracker CK17A

Brand: X10 Pages: 1

Brand: Waycon Pages: 8

Brand: Wavetronix Pages: 4

Brand: X10 Pages: 2

Brand: EUROM Pages: 28

Brand: Ultra-tow Pages: 14

Brand: KERN Pages: 4

Brand: Menabo Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands