manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual, Page: 158 / 241

Share
Download
Honeywell ORBIT 7120PLUS User Manual Download Page 158

144

Orbit 7120plus/7190g User Guide

Planet Code Check Digit

This selection allows you to specify whether the check digit should be transmitted 
at the end of Planet Code data. 

Default

=

Don’t Transmit.

Postnet Check Digit

This selection allows you to specify whether the check digit should be transmitted 
at the end of Postnet data. 

Default

=

Don’t Transmit.

Australian Post Interpretation

This option controls what interpretation is applied to customer fields in Australian 
4-State symbols. 

Bar Output

 lists the bar patterns in “0123” format. 

Numeric N Table

 causes that field to be interpreted as numeric data using the N 

Table. 

Alphanumeric C Table

 causes the field to be interpreted as alphanumeric data 

using the C Table. Refer to the Australian Post Specification Tables.

Combination C and N Tables

 causes the field to be interpreted using either the C 

or N Tables.

Transmit Check Digit

* Don’t Transmit Check Digit

Transmit Check Digit

* Don’t Transmit Check Digit

* Bar Output

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments