manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

CHAPTER

1

Orbit 7120plus/7190g User Guide

1

GET STARTED

About This Manual

This User’s Guide provides installation and programming instructions for the Orbit 
7120plus and Orbit 7190g hybrid presentation scanners. Product specifications, 
dimensions, warranty, and customer support information are also included.

Honeywell bar code scanners are factory programmed for the most common ter-
minal and communications settings. If you need to change these settings, pro-
gramming is accomplished by scanning the bar codes in this guide.

An asterisk (*) next to an option indicates the default setting.

Unpack Your Device

After you open the shipping carton containing the product, take the following 
steps:

•

Check for damage during shipment. Report damage immediately to the carrier
who delivered the carton.

•

Make sure the items in the carton match your order.

•

Save the shipping container for later storage or shipping.

Power Information

Use only a Listed Limited Power Source (LPS) or Class 2 type power supply with 
output rated 5 to 5.2Vdc, 1A.

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Larry vs Harry Canopy Assembly Manual preview
Canopy
Brand: Larry vs Harry Pages: 20
Napoleon Oakville Series Owner'S Manual preview
Oakville Series
Brand: Napoleon Pages: 72
Napoleon GDS60-1 Instructions preview
GDS60-1
Brand: Napoleon Pages: 4
Napoleon Allure Vertical Series Installation And Operation Manual preview
Allure Vertical Series
Brand: Napoleon Pages: 120
Parrot CK3300 Setup Information Manual preview
CK3300
Brand: Parrot Pages: 19
Parrot Minikit+ Quick Start Manual preview
Minikit+
Brand: Parrot Pages: 88
Parrot Minikit+ Information Sheet preview
Minikit+
Brand: Parrot Pages: 2
Parrot CK3100 LCD Specifications preview
CK3100 LCD
Brand: Parrot Pages: 2
Parrot MINIKIT CHIC User Manual preview
MINIKIT CHIC
Brand: Parrot Pages: 11
Parrot CK 3000 Evolution Installation Notes preview
CK 3000 Evolution
Brand: Parrot Pages: 8
Parrot CK 3000 Evolution User Manual preview
CK 3000 Evolution
Brand: Parrot Pages: 106
Xsens MTi Series User Manual And Technical Documentation preview
MTi Series
Brand: Xsens Pages: 53
NEEWER X1 Pro Instruction Manual preview
X1 Pro
Brand: NEEWER Pages: 58
OEM Audio Reference Series Manual preview
Reference Series
Brand: OEM Audio Pages: 29
XCM Xbox 360 Quick Manual preview
Xbox 360
Brand: XCM Pages: 11
BabySense Dreamer Manual preview
Dreamer
Brand: BabySense Pages: 76
Omron E3Z-LL Manual preview
E3Z-LL
Brand: Omron Pages: 16
DRO PROS Touch Probe Manual preview
Touch Probe
Brand: DRO PROS Pages: 2

Brands by name

Popular brands

Load more brands