Honeywell ORBIT 7120PLUS User Manual Download | Manualshive

Page: 191 / 241

background image

Orbit 7120plus/7190g User Guide

177

Concatenation of Multiple Commands

Multiple commands can be issued within one Prefix/Storage sequence. Only the
Tag, SubTag, and Data fields must be repeated for each command in the sequence.
If additional commands are to be applied to the same Tag, then the new command
sequence is separated with a comma (,) and only the SubTag and Data fields of the
additional command are issued. If the additional command requires a different Tag
field, the command is separated from previous commands by a semicolon (;).

Responses

The device responds to serial commands with one of three responses:

ACK

Indicates a good command which has been processed.

ENQ

Indicates an invalid Tag or SubTag command.

NAK

Indicates the command was good, but the Data field entry was out of
the allowable range for this Tag and SubTag combination, e.g., an
entry for a minimum message length of 100 when the field will only
accept 2 characters.

When responding, the device echoes back the command sequence with the status
character inserted directly before each of the punctuation marks (the period, excla-
mation point, comma, or semicolon) in the command.

Examples of Query Commands

In the following examples, a bracketed notation [ ] depicts a non-displayable
response.

Example:

What is the range of possible values for Codabar Coding Enable?

Enter:

cbrena*.

Response:

CBRENA0-1[ACK]

This response indicates that Codabar Coding Enable (CBRENA) has a range of val-
ues from 0 to 1 (off and on).

Example:

What is the default value for Codabar Coding Enable?

Enter:

cbrena^.

Response:

CBRENA1[ACK]

This response indicates that the default setting for Codabar Coding Enable
(CBRENA) is 1, or on.

Example:

What is the device’s current setting for Codabar Coding Enable?

Enter:

cbrena?.

«
...
189
190
191
192
193
...
»

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Brand: Acer Pages: 2

Brand: Acer Pages: 12

Brand: Acer Pages: 4

Brand: Kargo Master Pages: 5

Brand: Kappa Pages: 4

Brand: Mamiya Pages: 4

Brand: Vega Pages: 76

Brand: Makita Pages: 20

Brand: zenitech Pages: 16

Brand: Nautronic Pages: 7

Brand: NAPCO Pages: 16

Brand: Pivot Pages: 4

Brand: FormFit Pages: 2

Brand: Celestron Pages: 24

Brand: Kasanova Pages: 22

Brand: Romik Pages: 6

Brand: Kensington Pages: 82

Brand: EUFAB Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands