manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual, Page: 139 / 241

Share
Download
Honeywell ORBIT 7120PLUS User Manual Download Page 139

Orbit 7120plus/7190g User Guide

125

Plessey Check Character

No Check Character

 indicates that the scanner reads and transmits bar code data 

with or without a check character.

When Check Character is set to 

Validate, but Don’t Transmit

, the unit only reads 

Plessey bar codes printed with a check character, but will not transmit the check 
character with the scanned data. 

When Check Character is set to 

Validate and Transmit

, the scanner only reads 

Plessey bar codes printed with a check character, and will transmit this character at 
the end of the scanned data. 

Default = No Check Character.

Plessey A to X Conversion

When scanning Plessey bar codes, you can convert all “A” characters to “X.” This 
conversion applies to the data and the check characters. 

Default = A to X Conver-

sion Off

.

*  No Check Character

Validate, but Don’t Transmit

Validate and Transmit

*  A to X Conversion Off

A to X Conversion On

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments