manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual, Page: 63 / 241

Share
Download
Honeywell ORBIT 7120PLUS User Manual Download Page 63

Orbit 7120plus/7190g User Guide

49

Beep on BEL Character

You may wish to force the scanner to beep upon a command sent from the host. If 
you scan the 

Beep on BEL On

 bar code below, the scanner will beep every time a 

BEL character is received from the host. 

Default = Beep on BEL Off.

Centering

Use Centering to narrow the scanner’s field of view to make sure that when the 
scanner is hand-held, it reads only those bar codes intended by the user. For 
instance, if multiple codes are placed closely together, centering will insure that 
only the desired codes are read. Using the Centering features, the scanner can 
emulate the operation of older systems, such as linear laser bar code scanners.)

Note: To adjust centering when the scanner is in Presentation Mode, see 

Presentation 

Centering

(page 39). 

Single Code Centering

Scan Single Code Centering to target the bar code closest to the center of the 
image. Singling out a bar code in this manner increases scanning accuracy when 
there are multiple bar codes close together. 

Custom Centering Settings

Use the following settings to customize your centering window. If a bar code is not 
touched by a predefined window, it will not be decoded or output by the scanner. If 
centering is turned on by scanning 

Centering On

, the scanner only reads codes 

that pass through the centering window you specify using the 

Top of Centering 

Window

, 

Bottom of Centering Window

, 

Left

, and 

Right

 

of Centering Window

 bar 

codes. 

*Beep on BEL Off

Beep on BEL On

Single Code Centering

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments