manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

156

Orbit 7120plus/7190g User Guide

F - File Format

Indicates the desired format for the image. 

0F

KIM format 

1F

TIFF binary

2F

TIFF binary group 4, compressed

3F

TIFF grayscale

4F

Uncompressed binary (upper left to lower right, 1 pixel/bit, 0 padded end 
of line)

5F

Uncompressed grayscale (upper left to lower right, bitmap format)

6F

JPEG image 

(default)

8F

BMP format (lower right to upper left, uncompressed)

10F

TIFF color compressed image

11F 

TIFF color uncompressed image

12F

JPEG color image

14F

BMP color format

15F

BMP Uncompressed raw image

H - Histogram Stretch

Increases the contrast of the transmitted image. Not available with some image 
formats. 

0H

No stretch 

(default)

1H

Histogram stretch

Example:

Histogram Stretch at 0H:

Histogram Stretch at 1H:

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

Manfrotto 625 Instructions preview
625
Brand: Manfrotto Pages: 2
Accessory Power ReVIVE series Manual preview
ReVIVE series
Brand: Accessory Power Pages: 36
Young Living Aria Operation Manual preview
Aria
Brand: Young Living Pages: 41
Hama Multi Operating Instructions Manual preview
Multi
Brand: Hama Pages: 40
Rave Sports SUP User Manual & Owners Manual preview
SUP
Brand: Rave Sports Pages: 16
RAKINDA F6 Manual preview
F6
Brand: RAKINDA Pages: 20
ZALMAN Z3 Series User Manual preview
Z3 Series
Brand: ZALMAN Pages: 20
WÄRTSILÄ RS24 User Manual preview
RS24
Brand: WÄRTSILÄ Pages: 64
Oki OKICOLOR8n Replacement Instructions preview
OKICOLOR8n
Brand: Oki Pages: 4
Zircon StudSensor HD25 Instructions preview
StudSensor HD25
Brand: Zircon Pages: 2
HBX ORC-0100 Installation Manual preview
ORC-0100
Brand: HBX Pages: 12
Stobag Melano TP7000 Manual preview
Melano TP7000
Brand: Stobag Pages: 3
texet PowerPack TPB-2112 User Manual preview
PowerPack TPB-2112
Brand: texet Pages: 16
Montech 508816 Assembly Instructions Manual preview
508816
Brand: Montech Pages: 17
Shenzhen NAS-PD02Z Instruction Manual preview
NAS-PD02Z
Brand: Shenzhen Pages: 13
R&G CP0479 Fitting Instructions Manual preview
CP0479
Brand: R&G Pages: 13
EcoFlow River Bank Manual preview
River Bank
Brand: EcoFlow Pages: 42
Kodak Vision Premier 2393 Technical Data Manual preview
Vision Premier 2393
Brand: Kodak Pages: 6

Brands by name

Popular brands

Load more brands