manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual

The Honeywell ORBIT 7120PLUS is a state-of-the-art barcode scanner designed for efficient and accurate scanning. Enhance your productivity with its user-friendly design and advanced scanning technology. To get started, simply download the free user manual from manualshive.com to fully unlock the potential of this exceptional product.

Share
Download
background image

Orbit 7120plus/7190g User Guide

3

1. Turn off power and disconnect the keyboard cable from the back of the termi-

nal/computer.

2. Connect the appropriate interface cable to the device and to the terminal/

computer.

Note:

The power supply must be ordered separately, if needed.

3. Turn the terminal/computer power back on. The scanner beeps.

4. Verify the scanner operation by scanning a bar code from the 

Sample Symbols

 

on page 223. The scanner beeps once. 

The unit defaults to an IBM PC AT and compatibles keyboard wedge interface with 
a USA keyboard. A carriage return (CR) suffix is added to bar code data. 

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments

Related manuals for ORBIT 7120PLUS

D-Link DCS-60 Technical Specifications preview
DCS-60
Brand: D-Link Pages: 2
Napoleon HD35 Instructions preview
HD35
Brand: Napoleon Pages: 4
hager Dream Installation Manual preview
Dream
Brand: hager Pages: 4
Harken Hoister SUP Manual preview
SUP
Brand: Harken Hoister Pages: 12
Federal Signal Corporation Vision SLR Quick Disconnect Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
Federal Signal Corporation Vision SLR Supplement Manual preview
Vision SLR
Brand: Federal Signal Corporation Pages: 8
FeiYu Tech WG2 Instruction Manual preview
WG2
Brand: FeiYu Tech Pages: 14
IFM KB Operating Instructions Manual preview
KB
Brand: IFM Pages: 12
IFM O3D3 Series Quick Reference Manual preview
O3D3 Series
Brand: IFM Pages: 13
IFM Efector 200 Series Operating Instructions preview
Efector 200 Series
Brand: IFM Pages: 4
IFM OY Series Operating Instructions Manual preview
OY Series
Brand: IFM Pages: 33
Kargo Master 40131 Installation Manual preview
40131
Brand: Kargo Master Pages: 5
Obelink LIVING Pitching Instruction preview
LIVING
Brand: Obelink Pages: 2
Leuze SET-AC Manual preview
SET-AC
Brand: Leuze Pages: 9
Paso CMDS Series Complementary Instructions Sheet preview
CMDS Series
Brand: Paso Pages: 29
SICK RSB Operating Instructions Manual preview
RSB
Brand: SICK Pages: 184
Kodak AE-31 Technical Data preview
AE-31
Brand: Kodak Pages: 2
aXtion Bold Installation Manual preview
Bold
Brand: aXtion Pages: 4

Brands by name

Popular brands

Load more brands