manualshive.com logo in svg

Honeywell ORBIT 7120PLUS, User Manual, Page: 81 / 241

Share
Download
Honeywell ORBIT 7120PLUS User Manual Download Page 81

Orbit 7120plus/7190g User Guide

67

Step 7.

Scan 

Save

 to save your data format, or 

Discard

 to exit without saving your 

changes.

Other Programming Selections

•

Clear One Data Format 

This deletes one data format for one symbology. If you are clearing the primary 
format, scan 

0

 from the 

Programming Chart,

 beginning on page 225. If you are 

clearing an alternate format, scan 

1

, 

2

, or 

3

, depending on the format you are 

clearing. Scan the Terminal Type and Code I.D. (see 

Symbology Charts

 on page 

211), and the bar code data length for the specific data format that you want to 
delete. All other formats remain unaffected.

•

Clear all Data Formats

This clears all data formats.

•

Save

Exit and save your data format changes.

•

Discard

Exit without saving any data format changes.

Enter Data Format 

Save

Discard

Clear One Data Format

Clear All Data Formats

Save

Discard

Summary of Contents for ORBIT 7120PLUS


















































































































































































































































Reviews:

No comments