HIKVISION DS-K3B601S Series User Manual Download

Page: 92 / 124

Figure 7-11 Select Card Reader Authentication Mode

Note

PIN refers to the PIN code set to open the door. Refer to Configure Access Control

Information .

2) Check the modes in the Available Mode list and they will be added to the selected modes

list.

3) Click OK.

After selecting the modes, the selected modes will display as icons with different color.

4. Click the icon to select a card reader authentication mode, and drag the cursor to draw a color

bar on the schedule, which means in that period of time, the card reader authentication is valid.

5. Repeat the above step to set other time periods.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands