HIKVISION DS-K3B601S Series User Manual Download | Manualshive

Page: 47 / 124

background image

Chapter 6 Activation

You should activate the device before the first login. After powering on the device, the system will

switch to Device Activation page.
Activation via the device, SADP tool and the client software are supported.
The default values of the device are as follows:
• The default IP address: 192.0.0.64

• The default port No.: 8000

• The default user name: admin

6.1 Activate via SADP

SADP is a tool to detect, activate and modify the IP address of the device over the LAN.
Before You Start
• Get the SADP software from the supplied disk or the official website http://

www.hikvision.com/en/ , and install the SADP according to the prompts.

• The device and the PC that runs the SADP tool should be within the same subnet.
The following steps show how to activate a device and modify its IP address. For batch activation

and IP addresses modification, refer to User Manual of SADP for details.
Steps

1. Run the SADP software and search the online devices.

2. Find and select your device in online device list.

3. Input new password (admin password) and confirm the password.

Caution

STRONG PASSWORD RECOMMENDED-We highly recommend you create a strong password of

your own choosing (using a minimum of 8 characters, including upper case letters, lower case

letters, numbers, and special characters) in order to increase the security of your product. And

we recommend you reset your password regularly, especially in the high security system,

resetting the password monthly or weekly can better protect your product.

4. Click Activate to start activation.

DS-K3B601SX Series Swing Barrier User Manual

33

«
...
45
46
47
48
49
...
»

Summary of Contents for DS-K3B601S Series





























































































































Reviews:

No comments

Related manuals for DS-K3B601S Series

Brand: Whirlpool Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands