HIKVISION DS-K3B601S Series User Manual Download Page 84

Page: 84 / 124

If enabling the function, user can present card on the card reader. If disabling the function,

the card reader for entrance cannot be used.

OK LED Polarity/Error LED Polarity/Buzzer Polarity

Set OK LED Polarity/Error LED Polarity/Buzzer LED Polarity of main board according to the

card reader parameters. Generally, adopts the default settings.

Buzzing Time

Set the card reader buzzing time. The available time ranges from 0 to 5,999s. 0 represents

continuous buzzing.

Max. Interval When Entering PWD

When you inputting the password on the card reader, if the interval between pressing two

digits is larger than the set value, the digits you pressed before will be cleared automatically.

Tampering Detection

Enable the anti-tamper detection for the card reader.

Communicate with Controller Every

When the access control device cannot connect with the card reader for longer than the set

time, the card reader will turn offline automatically.

Fingerprint Recognition Level

Select the fingerprint recognition level in the drop-down list.

5. Click OK.

6. Optional: Click Copy to, and then select the card reader(s) to copy the parameters in the page

to the selected card reader(s).

Configure Parameters for Alarm Output

After adding the access control device, if the device links to alarm outputs, you can configure the

parameters.
Before You Start

Add access control device to the client, and make sure the device supports alarm output.
Steps

1. Click Access Control → Advanced Function → Device Parameter to enter access control

parameter configuration page.

2. In the device list on the left, click to expand the door, select an alarm input and you can edit

the alarm input's parameters on the right.

3. Set the alarm output parameters.

Name

Edit the card reader name as desired.

Alarm Output Active Time

How long the alarm output will last after triggered.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands