HIKVISION DS-K3B601S Series User Manual Download Page 37

Page: 37 / 124

4.5.5 RS-485 Wiring

Note

• There are four RS-485 interfaces, which are for connecting ID card reader, IC card reader, QR

code scanner, fingerprint and card reader, card recycler, fingerprint reader, and face recognition

terminal. Take the wiring of RS-485 card reader as an example.

• When connecting the RS-485 interface with a card reader, the default entrance address is 1 and

the exit address is 4.

• If there are more than 1 RS-485 devices connected, the RS-485 ID cannot be conflicted.

4.5.6 RS-232 Wiring

Note

There are three RS-232 interfaces (UART4, UART7, and UART8). UART7 and UART8 can connect QR

code scanner, and card recycler, while UART4 can connect QR code scanner, card recycler, and face

recognition terminal.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands