HIKVISION DS-K3B601S Series User Manual Download

Page: 61 / 124

Figure 7-2 Configure Basic Information

Note

Once validity period expired, the credentials and access control settings of the person will be

invalid and the person will have no authorization to access the doors\floors. You can click

Extend to extend the person's validity period for 1 month, 3 months, 6 months, or 1 year.

5. Confirm to add the person.

Click Add to add the person and close the Add Person window.

Click Add and New to add the person and continue to add other persons.

7.4.3 Issue a Card by Local Mode

If a card enrollment station is available, you can issue a card by local mode. To read the card

number, you should connect the card enrollment station to the PC running the client by USB

interface or COM, and place the card on the card enrollment station.
Steps

1. Enter Person module.

2. Select an organization in the organization list to add the person and click Add to enter Add

Person panel.

Note

Enter the person's basic information first. For details about configuring person's basic

information, refer to Configure Basic Information .

3. In the Credential → Card area, click +.

4. Click Settings to enter the Settings page.

5. Select Local as the card issuing mode.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands