HIKVISION DS-K3B601S Series User Manual Download

Page: 22 / 124

Chapter 3 Installation

3.1 Disassemble Pedestals

Before installation, you should use the key to open the pedestals.
View the pictures below to find the lock holes.

Figure 3-1 Lock Holes

3.2 Install Pedestals

Before You Start

Prepare for the installation tools, check the device and the accessories, and clear the installation

base.
Steps

Note

• The device should be installed on the concrete surface or other non-flammable surfaces.

• If the installation area is too close to the wall, make sure the distance between the pedestal and

the wall should be more than 10 mm, or you cannot open the pedestal's top panel.

1. Prepare for the installation tools, check the components, and prepare for the installation base.

2. Drill holes on the ground according to the installation holes on the pedestals and insert the

expansion sleeves.

3. According to the entrance and exit marks on the pedestals, move the pedestals to the

corresponded positions.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands