HIKVISION DS-K3B601S Series User Manual Download

Page: 33 / 124

Access Controlling Board Terminal Description

Door Lock (Relay)

D1-

Door 1 Relay Output (Dry Contact)

D1+
D2-

Door 2 Relay Output (Dry Contact)

D2+

Alarm Output

NO/NC1

Alarm Output Relay 1 (Dry Contact)

COM1
NO/NC2

Alarm Output Relay 2 (Dry Contact)

COM2
NO/NC3

Alarm Output Relay 3 (Dry Contact)

COM3
NO/NC4

Alarm Output Relay 4 (Dry Contact)

COM4

Network Interface

LAN

Network Accessing

Note

• The alarm input hardware interface is normally open by default. So only the normally open

signal is allowed. It can be linked to the buzzer of the card reader and access controller, and the

alarm relay output and open door relay output.

• The DIP of RS485 card ID is set as 1 and4 by default. 1 is for entering, and 4 is for exiting. Set the

DIP as 3 for connecting visitor card reader.

• The Wiegand card reader 1 and 2 respectively refer to the entering and exiting card reader.

• The alarm output supports relay output.

• For any requirements, the door lock can control the door barrier status of the third party. D1

controls the barrier opening for entrance, while D2 controls the door opening for exit. For

details, see Barrier Control Relay Output Mode .

• C3 and C4 in the event input can also be people counting interface. C3 controls people counting

for entrance, while C4 controls people counting for exit. When the access control board detects

signals in C3 and C4, the people number will be accumulated. For detailed information about

people counting and people number, see Configuring People Counting Parameters in User

Manual of iVMS-4200 AC Client Software.

• For detailed information about the DIP switch, see DIP Switch Description.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands