HIKVISION DS-K3B601S Series User Manual Download

Page: 44 / 124

Note

• Only one turnstile can pair the keyfob. If multiple turnstiles are in the pairing mode, the

keyfob will select only one of them to pair.

• For details about DIP switch value and meaning, see DIP Switch .

6. Optional: Go to System → User → Keyfob User on the remote control page of the client

software to delete the keyfob.

5.3 Initialize Device

Steps

1. Remove the JP11 jumper cap on the access control board.

Figure 5-1 Initialization Jumper Cap

2. Disconnect the power and reboot the device. The device buzzer buzzes a long beep.

3. When the beep stopped, plug the jumper cap back.

4. Disconnect the power and power on the device again.

Caution

The initialization of the device will restore all the parameters to the default setting and all the

device events are deleted.

DS-K3B601SX Series Swing Barrier User Manual

Summary of Contents for DS-K3B601S Series





























































































































Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands

HIKVISION DS-K3B601S Series, User Manual

Search results

Summary of Contents for DS-K3B601S Series

Reviews:

Related manuals for DS-K3B601S Series

Brands by name

Popular brands