HIKVISION DS-7200-SH User Manual Download Page 23

Page: 23 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

1.5 Rear Panel

DS-7204HVI/HFI/HWI-SH, DS-7204HVI-SV and DS-7204HWI-SV:

The rear panel of 7204HVI/HFI/HWI-SH, DS-7204HVI-SV and DS-7204HWI-SV DVR is shown in Figure

1.6.

Figure 1.6 Rear Panel of DS-7204HVI/HFI/HWI-SH, DS-7204HVI-SV and DS-7204HWI-SV

DS-7216HVI-SH, DS-7216HVI-SV and DS-7216HWI-SL:

The rear panel of DS-7216HVI-SH, DS-7216HVI-SV and DS-7216WI-SL DVR is shown in Figure 1.7.

Figure 1.7 Rear Panel of DS-7216HVI-SH and DS-7216HVI-SV

Note:

The rear panel of DS-7208HVI-SH/DS-7208HVI-SV/DS-7208HWI-SL provides 8 video input

interfaces.

DS-7216HFI-SH and DS-7216HWI-SH:

The rear panel of DS-7216HFI-SH and DS-7216HWI-SH is shown in Figure 1.8.

Figure 1.8 Rear Panel of DS-7216HFI-SH and DS-7216HWI-SH

Note:

The rear panel of DS-7208HFI-SH/DS-7208HWI-SH provides 8 video input interfaces.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 23 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: