HIKVISION DS-7200-SH User Manual Download Page 24

Page: 24 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

Table 1.7 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

VIDEO OUT

BNC connector for video output.

USB Interface

Connects USB mouse or USB flash memory devices.

HDMI

HDMI video output.

VGA

DB15 connector for VGA output. Display local video output and menu.

AUDIO IN

RCA connector for audio input.

AUDIO OUT

RCA connector for audio output.

LAN Interface

RJ45 10M/100M Ethernet interface.

RS-485 Interface

Connector for RS-485 devices. Connect the D+ and D- terminals to T+

and T- of PTZ receiver respectively.

12V

12VDC power supply.

POWER

Switch for turning on/off the device.

GND

Ground (needs to be connected when DVR starts up).

DS-7224/7232HVI-SH and DS-7224/7232HWI-SH:

The rear panel of DS-7232HVI-SH/DS-7232HWI-SH is shown in Figure 1.9.

9 10 11 13

Figure 1.9 Rear Panel of DS-7232HVI-SH and DS-7232HWI-SH

Note:

The rear panel of DS-7224HVI-SH/DS-7224HWI-SH provides 24 video input interfaces.

Table 1.8 Description of Rear Panel

No.

Item

Description

VIDEO IN

BNC connector for analog video input.

VIDEO OUT

BNC connector for video output.

USB Interface

Connects USB mouse or USB flash memory devices.

HDMI

HDMI video output.

VGA

DB15 connector for VGA output. Display local video output and menu.

AUDIO IN

RCA connector for audio input.

AUDIO OUT

RCA connector for audio output.

Alarm In/Out

Connector for alarm input/output.

LAN Interface

RJ45 10M / 100M / 1000M Ethernet interface.

RS-485 Interface

Connector for RS-485 devices. Connect the D+ and D- terminals to R+ and R-

terminals of PTZ receiver respectively.

12V

12VDC power supply.

POWER

Switch for turning on/off the device.

GND

Ground(needs to be connected when DVR starts up)

DS-7316HFI-SH and DS-7316HWI-SH:

The rear panel of DS-7316HFI-SH and DS-7316HWI-SH DVR is shown in Figure 1.10.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 24 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: