HIKVISION DS-7200-SH User Manual Download

Page: 91 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

management

Pause reverse

play/Reverse play/

Single-frame reverse

play

Pause play/Play/Single-

frame play

Stop

Speed up

Previous tag

Next tag

Tag search

Exit

Hide

Progress bar

Video type

bar

Notes:

Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to

locate special frames.

About video type bar: represents normal recording (manual or schedule); represents event

recording; represents smart search recording.

6.1.6 Playing Back by System Log

Purpose:

Play back record file(s) associated with channels after searching system logs.

Steps:

Enter Log Search interface.

Menu>Maintenance>Log Search

Figure 6.31 System Log Search Interface

Set search time and type and click

Search

button.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands