HIKVISION DS-7200-SH User Manual Download

Page: 179 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

177

13.4 Configuring More Settings

Steps:

Enter the General Settings interface.

Menu > Configuration > General

Click the

More Settings

tab to enter the More Settings interface.

Figure 13.4 More Settings Interface

Configure the following settings:

•

Device Name:

Edit the name of device.

•

Device No.:

Edit the serial number of device. The Device No. can be set in the range of 1~255, and

the default No. is 255.

•

CVBS Output Brightness:

Adjust the video output brightness.

•

Operation Timeout:

Set timeout time for menu inactivity. E.g., when the timeout time is set to

Minutes

, the system will exit from the current operation menu to live view screen after 5 minutes

of menu inactivity.

•

Menu Output Mode:

Select the menu output mode to Auto, HDMI/VGA or Main CVBS.

Notes:



When you select

Auto

, the device can automatically detect the HDMI/VGA output as the main

output and the CVBS output as the auxiliary output when it starts up.



After you have changed the output mode, you should restart the device to activate the new

settings.

•

Main CVBS Scaling:

Enable/disable video output scaling for main CVBS video output.

Click the

Apply

button to save the settings.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands