HIKVISION DS-7200-SH User Manual Download Page 26

Page: 26 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

Table 1.10 Description of Rear Panel

No.

Item

Description

MAIN VIDEO OUT

BNC connector for video output.

SPOT VIDEO OUT

BNC connector for spot video output.

VIDEO IN

BNC connector for analog video input.

CVBS AUDIO OUT

RCA connector for audio output. This connector is synchronized with

CVBS video output.

VGA AUDIO OUT

RCA connector for audio output. This connector is synchronized with

VGA video output.

LINE IN

RCA connector for two-way audio input.

AUDIO IN

RCA connector for audio input.

VGA

DB15 connector for VGA output. Display local video output and menu.

HDMI

HDMI video output.

USB Interface

Connects USB mouse or USB flash memory devices.

LAN Interface

RJ45 10M/100M/1000M Ethernet interface.

RS-232

Connector for RS-232 devices.

Termination Switch

RS-485 termination switch. Up position is not terminated.

Down is terminated with 120Ω resistance.

RS-485 Interface

Connector for RS-485 devices. Connect the T+ and T- terminals to the

R+ and R- terminals of PTZ receiver respectively.

Connect the D+ and D- terminals to Ta and Tb terminals of the controller.

For cascading devices, the first DVR’s D+ and D- terminals should be

connected with the D+ and D- terminals of the next DVR.

Alarm In/Out

Connector for alarm input/output.

eSATA

Connects external SATA HDD, DVD-R/W.

GND

Ground(needs to be connected when DVR starts up)

100~240VAC

100~240VAC power supply.

POWER

Switch for turning on/off the device.

DS-8100-SH:

The rear panel of DS-8100-SH DVR is shown in Figure 1.12.

Figure 1.12 Rear Panel of DS-8132HCI-SH, DS-8132HFSI-SH and DS-8132HWSI-SH

Note:

DS-8124HCI-SH, DS-8124HFSI-SH and DS-8124HWSI-SH models provide 24 video input interfaces

on the rear panel.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 26 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: