HIKVISION DS-7200-SH User Manual Download

Page: 188 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

186

FAQ

•

Why does my device make a beeping sound after booting?

The possible reasons for the warning beep on the device are as follows:

There is no HDD installed in the device.

The HDD is not initialized.

HDD error

To cancel the beeping sound and use the device without HDD, enter the Exception Settings interface. For detailed

information, see Chapter Handling Exception.

•

Why does the device seem unresponsive when operating with the IR remote control?

Please read through the section

Using the IR Remote Control

, and check:

a) The batteries are installed correctly in the remote, making sure that the polarities of the batteries are not

reversed.

b) The batteries are fresh and are not out of power.

c) The remote has not been tampered with.

d) There are no fluorescent lamps in use nearby.

•

Why does the PTZ seem unresponsive?

If the PTZ seem unresponsive, please check:

a) The RS-485 cable is properly connected.

b) The dome decoder type is correct.

c) The dome decoder speed configuration is correct.

d) The dome decoder address bit configuration is correct.

e) That the main board RS-485 interface is not broken.

•

Why is there no video recorded after setting the motion detection?

If there are no recorded video after setting the motion detection, please check:

a) The recording schedule is setup correctly by following the steps listed in

Configuring Record

b) The motion detection area is configured correctly (See

Configuring Motion Detection

c) The channels are being triggered for motion detection (See

Configuring Motion Detection

•

Why doesn’t the device detect my USB export device for exporting recorded files?

There’s a chance that the device and your USB device is not compatible. Please refer to our company’s website to

view a list of compatible devices.

•

My device is in Live View mode and the menu does not show up. It does not respond to the mouse or the

IR remote control.

Your device may be in auxiliary mode. This occurs when the

Main/Spot

on front panel or

VOIP

button on IR

remote control is pressed. To return to the previous mode of operation, press the

Main/Spot

VOIP

button again

and then press

Enter

button on the IR remote control.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands