manualshive.com logo in svg

HIKVISION DS-7200-SH, User Manual, Page: 79 / 188

Share
Download
HIKVISION DS-7200-SH User Manual Download Page 79

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR 

77 

 

 

 
 

2.   

About video type bar:     represents normal recording (manual or schedule);     represents event 

recording;     represents smart search recording. 

 

 

6.1.2 Playing Back by Time

 

 

 

Purpose:

 

 

Play back video files recorded in specified time duration. Multi-channel simultaneous playback and channel 

switch are supported. 

Steps:

 

 

1.  

Enter playback interface. 

 

Menu>Playback 

 

2.  

Check the checkbox before the channel to select channel(s) and click the 

Detail 

button to view the 

record information of the channel(s). You can click 

Previous 

or 

Next 

to select the day for viewing the 

record information. 

 

 

Figure 6.6 Record Information 

 

 

3.  

Click 

Back 

to return to the playback interface. 

 

4.  

Set search conditions and click the 

Playback 

button to enter Playback interface. 

Summary of Contents for DS-7200-SH





























































































































































































Reviews:

No comments