HIKVISION DS-7200-SH User Manual Download Page 84

Page: 84 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

play

Previous file

Next file

Video search

Exit

Hide toolbar

Progress bar

Video type bar

Note:

Playback progress bar: use the mouse to click any point of the progress bar or drag the progress bar to

locate special frames.

About video type bar: represents normal recording (manual or schedule); represents event

recording; represents smart search recording.

6.1.4 Playing Back by Event Search

Purpose:

Play back record files on one or several channels searched out by restricting event type (motion detection or

alarm input). Channel switch is supported.

Note:

Playback by alarm input search is supported by DS-7224/7232-SH, DS-7300-SH and DS-8100-SH

models only.

Steps:

Enter the playback interface.

Menu>Playback

Select

Event

tab to enter the Event Playback interface.

Select

Motion

Alarm Input

as the event type.

Set the start time and end time for the selected event.

Figure 6.16 Video Search by Alarm Input

Figure 6.17 Video Search by Motion Detection

Select the camera (s) for searching of motion detected triggered record files or select the alarm input (s)

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 84 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: