HIKVISION DS-7200-SH User Manual Download Page 56

Page: 56 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

Figure 5.3 Encoding Parameters-Main Stream

Set encoding parameters for main stream

Select

Record

to enter the main stream settings interface.

Select the camera for configuration.

Configure the following parameters for the Main Stream (Normal) and the Main Stream (Event):

•

Stream Type:

Set the stream type to be Video or Video & Audio.

•

Resolution:

Set recording at resolution of WD1, 4CIF, 2CIF, CIF or QCIF.

Note:

The WD1 resolution is supported by DS-7204HWI-SV, DS-7224/7232HVI-SH,

DS-7200HWI-SH, DS-7200HVI-SV, DS-7200HWI-SL, DS-7300HWI-SH, DS-7300HI-SH,

DS-8100HCI-SH and DS-8100HWSI-SH models.

•

Bitrate Type:

Set the bitrate type to be Variable or Constant.

•

Video Quality:

Set the video quality of recording, with 6 levels configurable.

•

Frame Rate:

Set the frame rate of recording.

•

Max. Bitrate Mode:

Set the mode to General or Customize (32-3072Kbps).

•

Max Bitrate (Kbps):

Select or customize the maximum bit rate for recording.

•

Max. Bitrate Range Recommended:

A recommended Max. bitrate range is provided for

reference.

Configure the pre-record, post-record time, expired time, redundant record (this option is only

available when the HDD mode is

Group

) and whether you want to record audio.

•

Pre-record:

The time you set to record before the scheduled time or event. For example, when

an alarm triggered the recording at 10:00, if you set the pre-record time as 5 seconds, the

camera records it at 9:59:55.

•

Post-record:

The time you set to record after the event or the scheduled time. For example,

when an alarm triggered the recording ends at 11:00, if you set the post-record time as 5

seconds, it records till 11:00:05.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

HIKVISION DS-7200-SH, User Manual, Page: 56 / 188

Search results

Summary of Contents for DS-7200-SH

Reviews: