HIKVISION DS-7200-SH User Manual Download

Page: 103 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

101

Figure 7. 11 Checkup of Export Result using USB Writer

7.1.3 Backing up by Event Search

Purpose:

Back up event-related record files using USB devices (USB flash drives, USB HDDs, USB writer), SATA

writer or eSATA HDD. Quick Backup and Normal Backup are supported.

Notes:

Backup by alarm input search is supported by DS-7224/7232-SH, DS-7300-SH and DS-8100-SH

models only.

The eSATA writer is supported by DS-7300-SH and DS-8100-SH models only.

Steps:

Enter Export interface.

Menu>Export>Event

Select

Motion

Alarm Input

as the event type.

Note:

The following steps have introduced the backup by motion detection triggered record files.

Perform the same operation for the backup by alarm triggered record files.

Set the start time and end time of the record files.

Select the camera (s) for searching.

Figure 7.12 Event Search for Backup

Click

Search

button to enter the Search Result interface.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands