HIKVISION DS-7200-SH User Manual Download

Page: 158 / 188

User Manual of DS-7200-SH/SV/SL and DS-7300/8100-SH Series DVR

156

10.7 Detecting Bad Sector

Purpose:

The bad sectors of a HDD may cause the system to slow down when reading or writing data. You can detect the

bad sectors of the HDD and thus to take immediate measures to repair it.

Steps:

Enter the Bad Sector Detection interface.

Menu>HDD>HDD Detect>Bad Sector Detection

Figure 10.20 Bad Sector Detection

Select a HDD and click

Detect

to start detecting.

Figure 10.21 Bad Sector Detecting

You can click

Pause

to pause the detection and click

Resume

to resume the detection.

If there is any error information about the HDD, you can click

Error info

to view the information.

Summary of Contents for DS-7200-SH





























































































































































































Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands

HIKVISION DS-7200-SH, User Manual

Search results

Summary of Contents for DS-7200-SH

Reviews:

Related manuals for DS-7200-SH

Brands by name

Popular brands